Can I Install a Bathtub Myself? Factors to Consider As Well As Actions
Can I Install a Bathtub Myself? Factors to Consider As Well As Actions
Blog Article
This article below relating to A Step-by-Step Guide to Installing a Bathtub is totally insightful. You should see for yourself.
Installing a bath tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably tough project. If the old tub is conveniently easily accessible, the project can move easily; if you need to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need a helper to vacate the old tub and also embeded in the new one. Make sure you have actually qualified yourself for the job and are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is much better to think about employing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This post will help you install a new bathtub in your bathroom if you have actually already bought a new bathtub and also don't require to alter the arrangement of your previous water system pipelines.
Your tools and also product checklist should make up the following:
Planning for the Installation
To start with, the sustaining framework provided with the bath should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be rather troublesome as a result of the limited gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipelines have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, position the tub in the needed position. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub until the spirit level checks out degree.
To set up taps, fit all-time low of the furthest versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the water as well as inspect all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub and likewise check the overflow outlet and the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the tub should wait till the bathtub has actually been utilized a minimum of when as this will certainly settle it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be connected to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, causing the water to pass through the wall surface in between the bathroom as well as the tiling, causing problems with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture rather very early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently available on the market. It is advisable to fit the tiles using water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I discovered that piece on Installing A Bathtub while doing a lookup on the internet. If you enjoyed our blog entry kindly be sure to share it. I am grateful for your time. Don't forget to check up our website back soon.
Book An Estimate Now
Report this page